MinnSpas | EZHotTubParts.com

LX WTC50M Circulation Pump – 230V, 1 Amp, 1-1/2″ Short Thread (Standard)

$249.99

Fits: spas with an LX WTC50M standard (short-thread) circulation pump, including the factory circ pump on Island Spas, Tropic Seas and Artesian Elite.

Common symptoms: no heat, flow errors, a pump that hums, runs hot or has stopped, or a drip from the shaft seal.

Compatibility: Not for Jacuzzi, Sundance or Dimension One: their unions need the long-thread version (Sundance, Jacuzzi, Dimension One).

Key specs: 230V · 1.0 amp · 1 speed · 48 frame · 1-1/2" MBT

Not sure? Send us a photo of your pump label and we’ll confirm it fits.

- +
⭐⭐⭐⭐⭐ 4.9/5 Google Rating
Guaranteed Safe Checkout

🚚 How fast will this ship? 95% of Balboa, Gecko & Waterway parts ship within 2 business days.

Need it overnighted? Read this first

LX WTC50M Circulation Pump – 230V, 1 Amp, 1-1/2″ Short Thread (Standard)

Shop: LX Circulation Pumps | LX Jet Pumps | 1-1/2″ Flat Gaskets

The LX WTC50M is one of the most common hot tub circulation pumps: a small 230V, 1-amp pump that runs your filtration and heating around the clock. This is the standard short-thread version, the same LX pump spa makers install at the factory, sold here as a plain replacement without a spa-brand price.

Compatibility & Installation

Match the label on your old pump: LX WTC50M, 230V, about 1 amp, with 1-1/2″ threaded suction on the front and discharge on the side. The pump ships with unions; move your old pump’s cord to the new motor and turn the wet end to your discharge position if needed. Jacuzzi, Sundance and Dimension One spas need the long-thread version: Sundance, Jacuzzi, Dimension One.

📄 Wiring Diagram & Wet-End Rotation Guide (PDF) — 230V hookup and how to turn the wet end to the 3:00 or 9:00 position.

Specifications

  • Pump: LX WTC50M circulation pump, standard (short-thread) wet end
  • Voltage: 220–240V, 60 Hz
  • Amperage: 1.0 amp
  • Speeds: 1 speed, continuous duty
  • Motor frame: 48 frame, thru-bolt
  • Suction: 1-1/2″ male buttress thread (MBT), center
  • Discharge: 1-1/2″ MBT, side
  • Drain plugs: 6 and 9 o’clock
  • Motor label: 0.25 kW, 1700 RPM, IP55, UL listed
  • Size: about 11-7/8″ long × 6-1/2″ wide × 7-11/16″ tall

What’s in the Box

One LX WTC50M standard circulation pump (motor and wet end), two 1-1/2″ pump unions and a cord strain-relief fitting. No power cord is included, and the flat union gaskets are sold separately (1-1/2″ flat gasket 2-pack).

Common Symptoms of a Failing Circulation Pump

  • Spa won’t heat, or heats slowly
  • Flow or pressure-switch errors on the topside
  • Pump hums but doesn’t spin, or trips the breaker
  • Loud bearing noise or grinding
  • Water leaking from under the pump (shaft seal)

Replacement Information

Also sold as WTC50MSTD, WTC50M-STANDARD and LX-WTC50M-STANDARD, and used by Artesian as factory part 21-0015-81. The factory-packaged Artesian version (shipped from Artesian, with cord) is listed under each Artesian brand; this listing is the same LX pump for any spa that uses it. It does not replace Sundance / Jacuzzi 6500-907; that takes the long-thread pump.

Before You Install

  • Turn the spa off at the breaker before you open the equipment bay.
  • Confirm your old pump’s label reads 230V and about 1 amp. This pump is 230V only.
  • Close the slice valves (or drain the spa) before you undo the unions.
  • Fit new union gaskets, hand-tighten the unions, then fill and check for leaks before you close the cabinet.
  • If the wiring is beyond your comfort level, have a qualified spa technician do the hookup.
✅ Not Sure It Fits? Verify Before Ordering

Hot tub part compatibility can vary by spa brand, model, year, serial number, control system, and part revision.

To help us identify the correct replacement part, please send clear photos of:

  • Your existing part label or sticker
  • Your spa serial number sticker
  • The equipment area or installation location (if accessible)

EZ Hot Tub Parts can help confirm fitment before you order and help reduce costly returns.


Frequently Asked Questions

Yes. Artesian’s factory circulation pump (21-0015-81) is this LX WTC50M standard pump. This listing is the plain LX pump at a commodity price, shipped without a cord. If you’d rather have the factory-packaged version from Artesian with a cord, see our OEM Island Spas circulation pump.

Same motor, same rating. The long-thread (WTC50M-USA, also sold as WTC50MLS) has longer threads on the wet end so it can reach Jacuzzi and Sundance unions. This standard version (WTC50MSTD / WTC50M-STANDARD) has the shorter threads used on most other spas, and it will not replace Sundance / Jacuzzi 6500-907.

Both show up on this pump: suppliers list it as 1/15 HP, 1/3 HP or 0.35 HP, and the motor label itself says 0.25 kW. Horsepower isn’t a reliable way to match a circ pump. Match the voltage (230V), the amps (1.0A) and the 1-1/2″ threaded connections instead.

No. It ships with unions and a cord strain-relief fitting, but no cord. Move the cord from your old pump; the wiring diagram PDF shows the 230V hookup (black to live, white to neutral, green to ground).

Yes. Pull the four motor bolts, rotate the wet end to the 3:00 or 9:00 position, and tighten the bolts again. The steps and photos are in the PDF on this page.

Measure first. This pump is about 11-7/8″ long overall. Our techs often have to slide the spa pack over when it replaces the older, shorter Balboa circ pump, and it can touch the jet pump. If space is tight, the WE14 circulation pump is about 9-1/2″ long.

Two 1-1/2″ flat union gaskets. We sell them as a 2-pack; replace them any time the unions are opened.

WTC50MSTD WTC50M-STANDARD WTC50MSTANDARD LXWTC50MSTANDARD LX-WTC50M-STANDARD WTC50M standard short thread 34-343-1075 390598 21-0015-81 21-0015-81B LX circ pump

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Shopping Cart
Scroll to Top