MinnSpas | EZHotTubParts.com

Dimension One Circulation Pump – 230V, 1 Amp, 1-1/2″ – Long-Thread Replacement

$184.99

Fits: Dimension One spas with a 230V, 1-amp circulation pump on 1-1/2″ threaded unions.

Common symptoms: No heat or slow heating, a flow error, a circ pump that is noisy, humming or stopped, or a drip from the pump seal.

Compatibility: Match your old pump’s label (230V, about 1 amp) and its 1-1/2″ threaded connections. The long threads reach deep-set unions.

Key specs: 230V · 1.0 amp · 1 speed · 48 frame · 1-1/2" threaded

Not sure? Send us a photo of your pump label and we’ll confirm it fits.

- +
⭐⭐⭐⭐⭐ 4.9/5 Google Rating
Guaranteed Safe Checkout

🚚 How fast will this ship? 95% of Balboa, Gecko & Waterway parts ship within 2 business days.

Need it overnighted? Read this first

Dimension One Circulation Pump – 230V, 1 Amp, 1-1/2″ – Long-Thread Replacement

Shop: Dimension One Circulation Pumps | Dimension One Parts | 1-1/2″ Flat Gaskets

Your Dimension One’s circulation pump moves water through the filter and heater all day, so when it quits the spa stops heating. This replacement is the LX WTC50M with the long-thread wet end, a 1-amp, 230V pump with 1-1/2″ threaded connections. Match it to the label on the pump you’re replacing, not to the spa model.

Compatibility & Installation

The discharge ships pointing up. Turn the wet end to the position your old pump used (3:00 or 9:00) by pulling the four motor bolts, rotating, and re-tightening. Move the cord from your old pump to the terminal block as shown in the wiring diagram, then reconnect the unions with new gaskets.

📄 Wiring Diagram & Wet-End Rotation Guide (PDF) — 230V hookup (black to live, white to neutral, green to ground) and how to turn the wet end to the 3:00 or 9:00 position.

Specifications

  • Pump: LX WTC50M circulation pump, long-thread wet end
  • Voltage: 230V, 60 Hz
  • Amperage: 1.0 amp
  • Speeds: 1 speed, continuous duty
  • Motor frame: 48 frame
  • Suction: 1-1/2″ threaded, center
  • Discharge: 1-1/2″ threaded, side discharge
  • Horsepower / speed: 1/15 HP, 1700 RPM
  • Overall size: about 13-7/8″ long × 8-1/8″ tall
  • Ships: discharge pointing up (12 o’clock); turn the wet end to 3 or 9 o’clock to match your plumbing

What’s in the Box

One LX WTC50M long-thread circulation pump (motor and wet end) with pump unions. No power cord is included, and the flat union gaskets are sold separately (1-1/2″ flat gasket 2-pack). Your old pump’s cord moves over to the new motor.

Common Symptoms of a Failing Circulation Pump

  • Spa won’t heat, or heats slowly
  • Flow or pressure-switch errors on the topside
  • Pump hums but doesn’t spin, or trips the breaker
  • Loud bearing noise or grinding
  • Water leaking from under the pump (shaft seal)

Replacement Information

This is an LX replacement pump, not a Dimension One factory part, and Dimension One has used more than one circulation pump over the years. Before you order, check the label on your current pump for 230V and about 1 amp, and check that its suction and side discharge are 1-1/2″ threaded unions. If anything doesn’t match, or the label is gone, send us a photo and we’ll confirm the right pump.

Before You Install

  • Turn the spa off at the breaker before you open the equipment bay.
  • Confirm the label on your old pump reads 230V and about 1 amp. This pump is 230V only.
  • Close the slice valves (or drain the spa) before you undo the pump unions.
  • Fit new union gaskets, hand-tighten the unions, then fill and check for leaks before you close the cabinet.
  • If the wiring is beyond your comfort level, have a qualified spa technician do the hookup.
✅ Not Sure It Fits? Verify Before Ordering

Hot tub part compatibility can vary by spa brand, model, year, serial number, control system, and part revision.

To help us identify the correct replacement part, please send clear photos of:

  • Your existing part label or sticker
  • Your spa serial number sticker
  • The equipment area or installation location (if accessible)

EZ Hot Tub Parts can help confirm fitment before you order and help reduce costly returns.


Frequently Asked Questions

It fits Dimension One spas whose circulation pump is 230V, about 1 amp, with 1-1/2″ threaded suction and side discharge. Dimension One has used different circ pumps over the years, so compare your old pump’s label, or send us a photo and we’ll check it before you order.

On the motor housing, usually on top or on the side facing the cabinet door. Photograph it along with the front of the pump so we can see the fittings.

Yes. Remove the four motor bolts, rotate the wet end to 3:00 or 9:00 and tighten the bolts again. The rotation steps are in the PDF on this page.

A pair of 1-1/2″ flat union gaskets. Reuse your existing power cord.

WTC50M-USA WTC50MLS WTC50M long snout long thread LX Dimension One D1 circulation pump circ pump

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Shopping Cart
Scroll to Top