Jacuzzi Circulation Pump – 230V, 1 Amp, 1-1/2″ – Long-Thread Replacement
Shop: Jacuzzi Circulation Pumps | Jacuzzi Parts | 1-1/2″ Flat Gaskets
Jacuzzi hot tubs and Sundance spas are built by the same company and share the 1-1/2″ circulation pump that keeps the water filtering and heating. This replacement is the LX WTC50M with the long-thread wet end. Jacuzzi pump unions need the longer threads, and the short-thread WTC50M sold elsewhere won’t seal.
Compatibility & Installation
Out of the box the discharge points up. To match your Jacuzzi’s plumbing, loosen and pull the four motor bolts, rotate the wet end to the 3:00 or 9:00 position, and re-seat the bolts. Reconnect your existing cord using the wiring diagram, then reconnect the unions with fresh gaskets and leak-test before closing the cabinet.
📄 Wiring Diagram & Wet-End Rotation Guide (PDF) — 230V hookup (black to live, white to neutral, green to ground) and how to turn the wet end to the 3:00 or 9:00 position.
Specifications
- Pump: LX WTC50M circulation pump, long-thread wet end
- Voltage: 230V, 60 Hz
- Amperage: 1.0 amp
- Speeds: 1 speed, continuous duty
- Motor frame: 48 frame
- Suction: 1-1/2″ threaded, center
- Discharge: 1-1/2″ threaded, side discharge
- Horsepower / speed: 1/15 HP, 1700 RPM
- Overall size: about 13-7/8″ long × 8-1/8″ tall
- Ships: discharge pointing up (12 o’clock); turn the wet end to 3 or 9 o’clock to match your plumbing
What’s in the Box
One LX WTC50M long-thread circulation pump (motor and wet end) with pump unions. No power cord is included, and the flat union gaskets are sold separately (1-1/2″ flat gasket 2-pack). Your old pump’s cord moves over to the new motor.
Common Symptoms of a Failing Circulation Pump
- Spa won’t heat, or heats slowly
- Flow or pressure-switch errors on the topside
- Pump hums but doesn’t spin, or trips the breaker
- Loud bearing noise or grinding
- Water leaking from under the pump (shaft seal)
Replacement Information
This pump replaces the shared Jacuzzi / Sundance 230V, 1-amp circulation pump with 1-1/2″ threaded plumbing. It is not a Jacuzzi-branded pump; it is the LX motor with the long-thread wet end that matches the factory pump’s electrical rating and plumbing. Jacuzzi has used other circulation pumps on some models (small 3/4″ barb inline pumps, for example). If your old pump doesn’t match the specs below, send us a photo before you order.
Before You Install
- Turn the spa off at the breaker before you open the equipment bay.
- Confirm the label on your old pump reads 230V and about 1 amp. This pump is 230V only.
- Close the slice valves (or drain the spa) before you undo the pump unions.
- Fit new union gaskets, hand-tighten the unions, then fill and check for leaks before you close the cabinet.
- If the wiring is beyond your comfort level, have a qualified spa technician do the hookup.
✅ Not Sure It Fits? Verify Before Ordering
Hot tub part compatibility can vary by spa brand, model, year, serial number, control system, and part revision.
To help us identify the correct replacement part, please send clear photos of:
- Your existing part label or sticker
- Your spa serial number sticker
- The equipment area or installation location (if accessible)
EZ Hot Tub Parts can help confirm fitment before you order and help reduce costly returns.
Frequently Asked Questions
It is a replacement, not the factory-branded pump. It matches the shared Jacuzzi / Sundance 230V, 1-amp, 1-1/2″ circulation pump (6500-907) in voltage, amperage and plumbing, with the long-thread wet end those spas need.
Look at the label on your current circulation pump: it should read 230V and about 1 amp, with 1-1/2″ threaded connections on the front and side. If the label is unreadable or the fittings are small barbs, send us a photo through the form on this page.
Most owners can. Turn off the breaker, close the valves, rotate the wet end to your discharge position, move the cord over, and reconnect the unions with new gaskets. The PDF on this page covers the wiring and the wet-end rotation.
The standard WTC50M has a short-thread wet end, and its threads are not long enough for the Jacuzzi / Sundance pump unions. This long-thread version is made for that plumbing, so it’s the one to buy.
It ships with pump unions but no cord and no flat gaskets. Reuse your cord and add the 1-1/2″ flat gasket 2-pack.
WTC50M-USA WTC50MLS WTC50M long snout long thread LX 6500-907 6500907 6500-905 6500-913 Jacuzzi circulation pump






Reviews
There are no reviews yet.