Sundance Spas Circulation Pump – 230V, 1 Amp, 1-1/2″ – Long-Thread Replacement
Shop: Sundance Circulation Pumps | Sundance Parts | 1-1/2″ Flat Gaskets
This is the circulation pump that runs your Sundance spa’s filtration and heating around the clock. It is an LX WTC50M with the long-thread wet end, the version whose threads are long enough to reach Sundance’s pump unions. The common short-thread WTC50M will not seal on Sundance plumbing, which is why this one is listed for Sundance.
Compatibility & Installation
The pump ships with the discharge pointing straight up. Most Sundance equipment bays need it on the side: pull the four motor bolts, turn the wet end to 3:00 or 9:00, then put the bolts back and tighten them. The PDF below shows each step. Then move your old pump’s cord to the new motor and reconnect the unions with new gaskets.
📄 Wiring Diagram & Wet-End Rotation Guide (PDF) — 230V hookup (black to live, white to neutral, green to ground) and how to turn the wet end to the 3:00 or 9:00 position.
Specifications
- Pump: LX WTC50M circulation pump, long-thread wet end
- Voltage: 230V, 60 Hz
- Amperage: 1.0 amp
- Speeds: 1 speed, continuous duty
- Motor frame: 48 frame
- Suction: 1-1/2″ threaded, center
- Discharge: 1-1/2″ threaded, side discharge
- Horsepower / speed: 1/15 HP, 1700 RPM
- Overall size: about 13-7/8″ long × 8-1/8″ tall
- Ships: discharge pointing up (12 o’clock); turn the wet end to 3 or 9 o’clock to match your plumbing
What’s in the Box
One LX WTC50M long-thread circulation pump (motor and wet end) with pump unions. No power cord is included, and the flat union gaskets are sold separately (1-1/2″ flat gasket 2-pack). Your old pump’s cord moves over to the new motor.
Common Symptoms of a Failing Circulation Pump
- Spa won’t heat, or heats slowly
- Flow or pressure-switch errors on the topside
- Pump hums but doesn’t spin, or trips the breaker
- Loud bearing noise or grinding
- Water leaking from under the pump (shaft seal)
Replacement Information
This pump is sold as a replacement for the Sundance circulation pump on 230V Sundance spas with 1-1/2″ plumbing. It is not a factory Sundance-branded pump; it is the LX motor and long-thread wet end that matches the factory pump’s voltage, amperage and plumbing. If your spa runs a different circ pump (3/4″ barb fittings, or a Laing-style inline pump), this is not your part; see our other Sundance circulation pumps.
Before You Install
- Turn the spa off at the breaker before you open the equipment bay.
- Confirm the label on your old pump reads 230V and about 1 amp. This pump is 230V only.
- Close the slice valves (or drain the spa) before you undo the pump unions.
- Fit new union gaskets, hand-tighten the unions, then fill and check for leaks before you close the cabinet.
- If the wiring is beyond your comfort level, have a qualified spa technician do the hookup.
✅ Not Sure It Fits? Verify Before Ordering
Hot tub part compatibility can vary by spa brand, model, year, serial number, control system, and part revision.
To help us identify the correct replacement part, please send clear photos of:
- Your existing part label or sticker
- Your spa serial number sticker
- The equipment area or installation location (if accessible)
EZ Hot Tub Parts can help confirm fitment before you order and help reduce costly returns.
Frequently Asked Questions
Yes. This LX WTC50M long-thread pump is a replacement for Sundance circulation pump 6500-907 (also cross-referenced to 6500-905 and 6500-913). Turn the wet end to your discharge position before installing. Not sure which pump you have? Send us a photo of the label.
The standard WTC50M has a short-thread wet end. Its threads are too short to engage Sundance’s pump unions, so it leaks or won’t tighten. This long-thread version (WTC50M-USA, also sold as WTC50MLS) is the one that fits.
No, that is how it ships. Remove the four motor bolts, rotate the wet end to the 3:00 or 9:00 position and re-tighten. The Wiring Diagram & Wet-End Rotation Guide PDF on this page shows it step by step.
No. Move the cord from your old pump. The 230V wiring is black to live, white to neutral and green to ground; the PDF shows the terminal block.
Often. Sundance spas won’t fire the heater without flow, so a dead or weak circ pump shows up as no heat or a flow error. Check that the circ pump runs and isn’t humming or hot before you replace the heater or sensors.
Two 1-1/2″ flat union gaskets. We sell them as a 2-pack; replace them whenever the unions are opened.
WTC50M-USA WTC50MLS WTC50M long snout long thread LX 6500-907 6500907 6500-905 6500-913 Sundance circulation pump






Reviews
There are no reviews yet.